WHAT IS IONIZATION? The process by which a neutral atom or molecule acquires
a positive or negative charge. WHAT IS AN ION? An ion is a charged atom or molecule. It is charged because
the number of electrons do not equal the number of protons in the atom
or molecule. An atom can acquire a positive charge or a negative charge
depending on whether the number of electrons in an atom is greater or
less than the number of protons in the atom WHAT IS A POOL IONIZER? In the case of Pool Ionizer or Mineral Purifier; it consists
of a low voltage DC power supply and a set or sets of sacrificial electrodes.
The electrodes can be made of pure copper or copper with alloys consisting
of anything from Silver to Zinc or any combination thereof. HOW DOES A POOL IONIZER WORK? When a set of electrodes are submerged in a solution, in
this case your Pool water and a DC electrical current is induced into
the electrodes, the positively charged electrode seeks the negatively
charged electrode. This attraction causes the copper electrode to give
up it's electrons. The electrons get swept away in the flow of the water
that is circulating in your pool water (pump system). These electrons
seek negatively charged surfaces such as the cell walls of Bacteria, Algae,
Viruses and Mold. Once they have found the negatively charged surfaces
of these organisms, they bond to them and disrupt the normal intake of
nutrients to the cell causing starvation of the undesirable organism,
this causes the mortality of the cell.
Short and simple: Ionization is a simple process, a DC voltage it generated across 2 copper electrodes in water, this causes electrolysis.
The electrodes shed their electrons which go down stream into your pool or spa, this kills germs algae and viruses.
You will not find a higher quality or better value anywhere in the world than the CRL-POOL-IONIZERS. WHY PAY MORE?
10
STEPS FOR A "PERFECT" POOL USING AN IONIZER, CLICK
HERE!

  
Dolphin / Pioneer Ionizer
Model D40-I/ P-25
Our Low Internet Price
Only $309
+ $20 S&H
|
SPECIFICATIONS D40-I
CAPACITY:
UP TO 35,000 GALLONS/ 151,000 LITERS
INPUT VOLTAGE: 120/240 VAC @ 50/60 Hz; Switchable
OUTPUT CAPACITY: 9 VDC @ 1A; Load dependent
OUTPUT EFFICIENCY: 95% Efficient across output spectrum
OUTPUT MODE: Regulated DC current at 100% of duty cycle; steady
state, load dependent.
POWER CONSUMPTION: 9 W Max. load dependent
CIRCUIT PROTECTION: Solid state transient; fused primary & secondary.
Continual load sampling with current limiting.
CONTROLLER DIMENSIONS: 4.5" X 4.5" X 2.0" (LxHxD)
CONTROLLER HOUSING: High impact polystyrene;
NEMA 4 rated
TEMPERATURE LIMITS: 32 degrees F Min. to 120 F degrees Max.
CONTROL PROCESSOR: Regulated DC current; power "ON" indicator,
diagnostic LED display
COMPLIANCE: ETL listed & approved;
EPA EST. NO. 69282-FL-1
ELECTRODE SIZE: 5 " LONG X . 5 " DIAMETER
ELECTRODE COMPOSITION: VIRGIN COPPER ALLOY
|
|
D40-I Model D40-I Features
1 YEAR WARRANTY
MEET OR EXCEED NSF, ETL, CE, UL STANDARDS
BUILT ACCORDING TO ISO-9000 STANDARDS
EPA EST. NO. 69282-FL-1
COPPER TEST KIT INCLUDED
HIGH QUALITY VIRGIN
COPPER ALLOY ELECTRODES
DIGITAL CONTROL PACKAGE
DIGITAL DISPLAY
SOLID STATE ELECTRONICS
2" TEES WITH 1-1/2" REDUCING BUSHINGS
AUTO-REVERSING POLARITY
TREATS UP TO 50,000 GALLONS (24 Hr. run time)
|

CLR-POOL-ION, DELUXE
Model CPI-3
3 LB Virgin Copper
Electrodes
CLR-POOL
IONIZER
UP TO 50,000 gallons
UP to 100,000
GAL. with additional electrodes see CPI-4 below.
$249 + $20 S&H
(enclosure may vary)
SPECIFICATIONS
INPUT VOLTAGE:
90~240 Volts AC
Auto Ranging.
INPUT FREQUENCY: 50 TO 60 HERTZ.
OUTPUT VOLTAGE: 12 VDC.
OUTPUT CURRENT: 3.5 AMPS. MAX.
CONTROLLER: WEATHER PROOF
FLOW RATE: 20 TO 120 GPM.
CELL: 2" PVC TEE with SEE THROUGH EXTENSION
CELL REPLACEMENT: HAND TIGHT UNION
ELECTRODE SIZE: 6 " LONG X 7/8" DIAMETER
(one of the heaviest electrodes available)
ELECTRODE COMPOSITION: 99.9% PURE COPPER
CAPACITY: UP TO 50,000 GALLONS
(189,256 litters)
CPI-4
100,000 GALLON CAPACITY
LIFETIME CONTROLLER WARRANTY**
(We will keep you ionizer running, you just buy your replacement electrodes from us, which are the highest quality and best prices anyway) That's it!
SAME AS THE CPI-3 BUT WITH AN ADDITIONAL SET OF ELECTRODES AND TEE HOUSING.
6 LBS OF VIRGIN COPPER ELECTRODE MATERIAL
$379 + $25 S&H (USA Shipping)
|
Model CPI-3 Features:
LIFETIME CONTROLLER WARRANTY**
(We will keep you ionizer running, you just buy your replacement electrodes from us, which are the highest quality and best prices anyway) That's it!
Adjustable Output for Precise Metering of Ion Production.
NEMA 4 Rated Weatherproof ALL ALUMINUM ENCLOSURE with built in mounting brackets .Protects Electronics
from Moisture, Corrosion, and Harsh Environments.
High Efficiency Auto Ranging Switching Power Supply with Fuse Protection and auto reset.
Solid State Electronic Circuitry with Automatic Sequential Polarity
Switching to keep Electrodes Clean and Even Wearing.
Light Emitting Diodes Display Power, Cell Power, and Polarity.
Electrode Cell has a 2" Tee Fitting with 1-1/2" Reducing Bushings.
See Through Section for Viewing of Electrodes, Hand Tighten
Union for Easy Removal of Electrodes, and Stainless Steel Connections
so there are No Corrosion Problems. Meets or Exceeds UL and NSF
Standards.
30 Day Satisfaction Guaranty:

|

CLR-POOL-ION, MIDLINE
Model CPI-2 Virgin Copper
Electrodes
(Enclosure & Electrode
shape may vary)
CLR-POOL
IONIZER
UP TO 25,000 GALLONS
$199 + $20 S&H
INPUT VOLTAGE 90- 240 Volts AC
Auto Ranging.
INPUT FREQUENCY: 50 TO 60 HERTZ.
OUTPUT VOLTAGE: 12 VDC.
OUTPUT CURRENT: 3.5 AMPS. MAX.
CONTROLLER: WEATHER PROOF
FLOW RATE: 20 TO 120 GPM.
CELL: 2" PVC TEE
ELECTRODE COMPOSITION: VIRGIN COPPER
CAPACITY: UP TO 25,000 GALLONS /
|
Model CPI-2 Features:
LIFETIME CONTROLLER WARRANTY**
(We will keep you ionizer running, you just buy your replacement electrodes from us, which are the highest quality and best prices anyway) That's it!
Adjustable Output for Precise Metering of Ion Production.
NEMA 4 ALUMINUM Weatherproof Equipment Enclosure with built in mounting brackets. Protects Electronics from Moisture, Corrosion, and Harsh Environments. Built for a lifetime of dependable service.
High Efficiency Auto Ranging Switching Power Supply.
Solid State Electronic Circuitry with Automatic Sequential Polarity Switching to keep Electrodes Clean and Even Wearing.
Light Emitting Diodes Display Power, Cell Power, and Polarity.
Electrode Cell has a 2" Tee Fitting with 1-1/2" Reducing Bushings If Needed, Meets or Exceeds UL and NSF Standards.
30 Day Satisfaction Guaranty,
!
|

CLR-POOL-ION, ECONOMY
Model CPI-1
Virgin Copper
Electrodes
CLR-POOL
IONIZER
UP TO 25,000
GALLONS
$99 + $20 S&H
Only $99
Model CPI-1 Specifications:
INPUT VOLTAGE: 120/ 240 VOLT MANUAL SWITCH
INPUT FREQUENCY: 50 TO 60 HERTZ.
OUTPUT VOLTAGE: 1.5-12 VDC.
OUTPUT CURRENT: 1 AMP. MAX.
CONTROLLER: WEATHER PROOF
FLOW RATE: 20 TO 120 GPM.
CELL: 2" THREADED PVC TEE
ELECTRODE SIZE: 3 " LONG (very heavy)
ELECTRODE COMPOSITION: Virgin Copper
CAPACITY: UP TO 25,000 GALLONS /
(94,500 liters)
|
Model CPI-1 Features
LIFETIME CONTROLLER WARRANTY**
(We will keep you ionizer running, you just buy your replacement electrodes from us, which are the best prices anyway) That's it!
Simple Low Cost System.
Comes with a Copper Test Kit.
Adjustable Output, and Polarity Switch.
Has Threaded Electrode Cell with a 2" Tee Fitting, and 1-1/2" Reducing Bushings if Needed.
30 Day Satisfaction Guaranty.
|
10
STEPS FOR A "PERFECT" POOL USING AN IONIZER. 1. SHOCK:
If your pool is not brand new, Filter and Shock the water to 5ppm chlorine
3-5 consecutive days or use a non-chlorine shock at 10ppm for 3-5 consecutive
days. 2. BALANCE:
Your pool should be pH balanced to 7.2- 7.6 pH. And tested weekly. 3. TOTAL DISSOLVED SOLIDS:
TDS should be at 750-1500 ppm. (UNLESS YOU HAVE A CHLORINE GENERATION
SYSTEM) 4. CYANURIC ACID (STABILIZER):
Ideal range should be 0-30 ppm (UNLESS YOU HAVE A CHLORINE GENERATION
SYSTEM) 5. HALOGEN:
Ideal range should be .4 ppm Chlorine OR .8 ppm Bromine. (STATE OR LOCAL
HEALTH CODES MAY VARY) 6. TOTAL ALKALINITY:
Ideal range should be 80-120 ppm (usually takes care of itself if pH is
balanced) 7. CALCIUM HARDNESS:
Ideal range should be 225-375 ppm. 8. INSTALL YOUR IONIZER:
Install your Ionizer following the directions of the Ionizer manufacturer. 9. COPPER ION LEVELS: (Ideal Range . 3 - . 4 PPM)
Run your Ionizer in conjunction with your pump system until you have obtained
the recommended level of copper Ions. Adjust pool pump times and output
levels of the Ionizer to continue to maintain . 3 - . 4 ppm copper. (a
copper test kit is usually supplied with the Ionizer, if not we have them.)
Click her for more info copper test kits. 10. ENJOY!!
Now that you have your ion levels adjusted according to your pump time,
you will be able to sit back and relax enjoying your mineral-infused pool,
knowing that your water has a FORMIDABLE first line of defense against
Bacteria, Viruses, Fungus, Yeast, and ALL FORMS OF ALGAE. WHAT ABOUT MAINTENANCE? The only maintenance needed for your Ionizer is checking
the electrodes once per year to ensure they are clean and there is a sufficient
amount of electrode left to maintain your copper levels. Because the electrodes are sacrificial, they will need
to be replaced periodically depending on your pool size and usage. CLICK
HERE FOR ELECTRODE INFORMATION Can Ionizers stain pools? (Rarely) There are 3 reasons why pools can become stained. !! All
ARE EASILY AVOIDABLE !! 1. The number one reason is due to improper use of oxidizing
materials (chlorine tablets or granules). People throw the tablets or
granules directly into the pool. The suspended copper Ions become oxidized
by the extremely powerful concentration of chlorine. This causes the copper
to fall out of suspension, this can cause staining where the tablets or
granules were dumped or even cause a ring around part of the pool. To avoid this, we recommend the use of LIQUID chlorine such
as clorox or any generic liquid bleach. 2. Pools can become stained if the Ionizer is allowed to
run unchecked for extended periods of time. To avoid this, check your Ion levels periodically. Usually
once a week is sufficient. 3. pH and temperature extremes combined. If your pool becomes
unbalanced on the alkaline side, (8.2 & UP) and the temperature is
very hot, you can run a risk of staining. To avoid this, simply maintain the recommended pH of 7.2
- 7.6
If staining occurs, not to worry..we have a pool stain treatment product
that will reverse the staining.
|
|
|
|
|
|
Other electrodes
click here
Electrodes
3" L x 9/16 "
2"Threaded
pipe fitting
Threaded
stainless steel electrical terminals
Virgin copper electrodes
Almost
18% more electrode than a 1/2" diameter electrode.
Model D15-IC
|
Other electrodes
click here
Electrodes,
CLR-POOL
CPIC-3
6"X 7/8"
APROX.
3 LB.
Threaded
stainless steel electrical terminals
Virgin
Copper
Model CPIC-3
|
Other electrodes
click here
Electrodes,
6" L x 9/16 "
2" Threaded
pipe fitting
Threaded
stainless steel electrical terminals Virgin copper electrodes PURE COPPER REPLACEMENT ELECTRODES FOR DOLPHIN 40, 50, AND 100 IONIZER MODELS PIONEER P-25, P-50/ P-100
Almost
18% more electrode than a 1/2" diameter electrode.
Model D100-IC
|
33% SILVER
67%
COPPER
CPIC-1AG OVER 1 LB
$389
IF YOU WANT MORE THAN JUST PURE COPPER AND YOU WANT THE SILVER LEVEL THAT NASA HAS PROVEN TO WORK!
2" MALE PIPE PLUG WITH 17 OZ ELECTRODES
MODEL
CPIC-AG 17OZ
|
33% SILVER
67%
COPPER
CPIC-1AG JUST UNDER 1LB
$369
IF YOU WANT MORE THAN JUST PURE COPPER AND YOU WANT THE SILVER LEVEL THAT NASA HAS PROVEN TO WORK!
2" MALE PIPE PLUG WITH 13 OZ ELECTRODES
MODEL
CPIC-AG 13OZ
|
| |
|
|
|
|
*Some sub-components may be made in other countries. |
|